THE FOUNDATION OF PLUMBING KNOWLEDGE FOR BATHTUB INSTALLATION

The Foundation of Plumbing Knowledge for Bathtub Installation

The Foundation of Plumbing Knowledge for Bathtub Installation

Blog Article

Book Today

They are making a number of great observations regarding Tools You Need to Install a New Bathtub in general in this article following next.


A Step-by-Step Guide to Installing a Bathtub
Mounting a bath tub isn't exactly brain surgery, but it does need solid plumbing, carpentry, as well as sometimes, tiling skills. Replacing an old tub with a new one is likewise a moderately difficult task. If the old bathtub is conveniently obtainable, the job can move easily; if you have to open up a wall surface to eliminate the old bathtub and also position the new bath tub, the task is a lot harder. In either case, the project is within a residence handyman's skills, although you will require a helper to leave the old bathtub and embeded in the new one. Make certain you have actually qualified yourself for the task and also are comfortable attempting it. Rather than employing a service provider to take over a halfway-completed project, it is better to think about utilizing one prior to you begin. Opportunities are you might need a specialist plumber to make tube links.
This article will assist you set up a new tub in your bathroom if you have actually already bought a new tub and do not need to change the plan of your previous water system pipes.
Your devices and product list ought to make up the following:
  • New Bathtub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Knife

  • Measuring tape

  • Pipe Caps


  • Planning for the Installment


    First of all, the supporting frame supplied with the bathroom ought to be fitted (if required) according to the maker's directions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is important to ensure that if the tap features a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is also sensible to fit a sustaining plate under the faucets device to avoid stress on the tub.
    Fit the flexible tap connectors to the bottom of both taps utilizing 2 nuts and also olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet through the hole in the bath. Utilize the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next, fit the end of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Make certain you utilize all of the supplied washing machines.
    Link the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath ought to now be ready to be suited its last placement.

    Removing Old Touches


    If you need to replace old taps with new ones as a part of your installment, then the first thing you should do is detach the supply of water. After doing so, switch on the faucets to drain any type of water remaining in the system. The procedure of eliminating the existing faucets can be quite bothersome as a result of the restricted access that is commonly the case.
    Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the faucets. Have a fabric prepared for the remaining water that will certainly originate from the pipes. As soon as the supply pipes have been gotten rid of, use the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this process. Once the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing compound.
    Before proceeding to fit the new faucets, compare the pipe links on the old faucets to the new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the new faucets to fit.

    Installing the Bathtub


    Using both wooden boards under its feet, position the bathtub in the needed setting. The wood boards are valuable in evenly spreading out the weight of the bathtub over the location of the boards rather than focusing all the weight onto four tiny points.
    The following objective is to make certain that the tub is leveled all round. This can be accomplished by inspecting the level and also readjusting the feet on the tub up until the spirit level reviews level.
    To set up faucets, fit all-time low of the furthest flexible tap port to the proper supply pipe by making a compression join; then do the very same for the various other faucet.
    Turn on the water system as well as examine all joints and also new pipework for leaks and also tighten them if required. Fill the tub and also examine the overflow outlet and the regular electrical outlet for leaks.
    Finally, fix the bathroom paneling as explained in the supplier's instruction manual. Tiling and securing around the bathtub needs to wait until the bath tub has actually been used at the very least once as this will certainly settle it right into its last position.

    Fitting New Touches


    If the tails of the new faucets are plastic, then you will need a plastic adapter to avoid damage to the string. One end of the adapter fits on the plastic tail of the tap and also the various other end gives a connection to the existent supply pipelines.
    If you need to fit a monobloc, after that you will certainly require minimizing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
    Next, position the faucet in the installing hole in the bath/basin ensuring that the washing machines remain in place in between the faucet and the sink. Safeguard the tap in position with the maker supplied backnut. Once the faucet is securely in place, the supply pipelines can be connected to the tails of the taps. The taps can either be linked by using corrugated copper piping or with normal faucet connectors. The previous kind must be linked to the tap finishes first, tightening just by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have actually been linked.

    Tiling Around the Bathtub


    In the location where the bathroom satisfies the tile, it is necessary to seal the accompanies a silicone rubber caulking. This is important as the fitting can move enough to break an inflexible seal, causing the water to penetrate the wall between the bathroom and the tiling, bring about difficulties with dampness and possible leakages to the ceiling listed below.
    You can pick from a range of coloured sealers to assimilate your components and fittings. They are sold in tubes as well as cartridges, and can sealing gaps up to a size of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill the bath tub with water prior to securing, to permit the activity experienced when the tub is in usage. The sealer can break relatively early if you do not consider this motion prior to sealing.
    Additionally, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also conveniently offered on the market. It is suggested to fit the tiles utilizing water-resistant or waterproof adhesive and also cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    Tools You Need to Install a New Bathtub

    Do you appreciate more info about How to Install a Bathtub? Place a remark down the page. We'd be glad to see your thoughts about this post. We are looking forward to see you back again in the future. Enjoyed our blog posting? Please share it. Let others check it out. Thanks for taking the time to read it.


    Book Now

    Report this page